335070 Carburetor Float Bowl Gasket Fits Evinrude / Johnson (90-175 HP)

Product Overview

XR MARINE · CARBURETORS & REPAIR KITS

335070 Carburetor Float Bowl Gasket Fits Evinrude / Johnson (90-175 HP)

This is a carburetor float-bowl gasket referenced to Evinrude / Johnson OEM numbers 335070 and 0335070. It is designed for servicing the carburetor float-bowl sealing joint on compatible 60° V4 and V6 2-stroke outboards rated at 90–175 HP from 1991 onward.

Please note that this product is an individual float-bowl gasket rather than a complete carburetor assembly, the float bowl housing itself, or a nozzle gasket. Always verify your installed carburetor's exact gasket reference and engine configuration before ordering.

Product Specifications

Key product details for identification and comparison.

Fitment

The 335070 Carburetor Float Bowl Gasket from XR Marine fits Evinrude and Johnson 90–175 HP 2-Stroke outboards when matched to 60° V4 and V6 carburetor float-bowl applications from 1991 onward in the model-year applications listed below.

Match the complete engine model designation on your identification plate against the individual entries below, compare the full OEM reference number from your carburetor parts list, and verify all configuration and cylinder bank angle restrictions. Horsepower and year alone are not enough to confirm fitment.

• Brand: Evinrude / Johnson (Johnson application scope) | Power: 90-175 HP | Year: 2001 | Stroke: 2-Stroke | Restriction: V4 engine configuration, 60° cylinder bank angle, carburetor float-bowl application, from 1991 onward (end year not stated)
  ! Check conditions
• Brand: Evinrude / Johnson (Johnson application scope) | Power: 90-175 HP | Year: 2001 | Stroke: 2-Stroke | Restriction: V6 engine configuration, 60° cylinder bank angle, carburetor float-bowl application, from 1991 onward (end year not stated)
  ! Check conditions
• Brand: Evinrude / Johnson (Evinrude application scope) | Power: 90-175 HP | Year: 2001 | Stroke: 2-Stroke | Restriction: V4 engine configuration, 60° cylinder bank angle, carburetor float-bowl application, from 1991 onward (end year not stated)
  ! Check conditions
• Brand: Evinrude / Johnson (Evinrude application scope) | Power: 90-175 HP | Year: 2001 | Stroke: 2-Stroke | Restriction: V6 engine configuration, 60° cylinder bank angle, carburetor float-bowl application, from 1991 onward (end year not stated)
  ! Check conditions

OEM & Part Number References

Use the complete reference number, including its suffix, when comparing parts. Reference numbers do not confirm that every version is interchangeable.

What's Included

Check the supplied components before planning your repair.

• Carburetor Float Bowl Gasket (OEM Reference: 335070; 0335070) — Included

Contact XR Marine to confirm the exact supplied piece count before ordering if your repair requires servicing multiple carburetors.

Installation Guide

General installation overview. Follow the service manual for your exact engine and carburetor configuration. Fuel-system work requires the appropriate skills and precautions.

1. Verify Part Identification and Prepare Safely: Confirm the engine model on the identification plate and match the gasket against your carburetor parts list (335070 / 0335070). Ensure the engine is shut off and cool, isolate the fuel supply and ignition system per your service manual, and work in a well-ventilated area away from any ignition sources.
2. Disassemble and Inspect the Float-Bowl Joint: Note the routing of fuel lines and linkages before accessing the carburetor float bowl. Remove the float bowl according to the service manual, carefully clean old gasket residue from the mating surfaces without gouging or warping the joint, and compare the new gasket profile directly with the original float-bowl sealing surface.
3. Reassemble and Check for Fuel Leaks: Seat the new float-bowl gasket properly in the joint and reassemble the float bowl following the tightening sequence and specifications in your service manual. Restore fuel supply, prime the system to inspect thoroughly for any fuel seepage around the bowl joint, and only perform a running test with proper cooling water supply connected. Stop immediately if any leak or abnormality occurs.

Before You Order

A careful fitment check helps you choose the right part the first time.

• Match the full engine model designation on the identification plate.
• Check the individual year entry and any serial-number or version restrictions.
• Compare the complete OEM reference number, including its suffix. Horsepower or appearance alone is not enough.
• Confirm the package contents and the quantity needed for your repair.
• Verify that your engine is a 60° V4 or V6 configuration (90–175 HP, 1991 onward) and that your carburetor uses float-bowl gasket reference 335070 or 0335070.
• Distinguish this float-bowl joint gasket from a nozzle gasket, a complete float bowl housing, or a full carburetor assembly.

Need help checking fitment? Have your engine identification details, the existing part number and clear photos ready when you contact XR Marine.

Why XR Marine

Frequently Asked Questions

Answers to common questions about this product and its application.

Related Parts

Review these related parts according to the relationship described below.

• Carburetor Float Bowl Gasket — 3-Pack: This single Carburetor Float Bowl Gasket (OEM Reference 335070; 0335070) is a component of the 3-Pack option (quantity: 3). The 3-Pack is a separate multi-pack option and is not included automatically with this listing.